Logitech X-530 Manual & Setup Once you have installed your drivers, you can enjoy your new speakers. There is no need to install the drivers manually. If you have an older model, you can try updating the driver using your computer’s control panel. The installation process is simple and will take you just a few minutes. This will help you to quickly get the drivers for your speakers. Once the drivers have been installed, you can now enjoy your new Logitech 5.1 speakers.
The X-530 has three analog miniplugs to connect to your PC’s sound card. They aren’t equipped with digital inputs. You can connect them to a 5.1-channel sound card, but there is no jack for iPod connection. The drivers are required for proper functioning of your speakers. When you have installed your drivers, you can now use your new speaker system. It’s important to update your speakers’ drivers regularly because the latest versions can cause problems.
The X-530 drivers will work well with any Mac operating system. Depending on the model you have, you may need to install the latest version of the drivers for your computer. You can also install the latest version of your driver by installing the latest Apple Mac OS update. The driver will be compatible with all versions of your Mac, so it is very important that you install the latest one for your PC. Once you have the updated driver, you should now be able to use your new devices on your Mac.
The X-530 is a good set of headphones for the home theater. They come in three sizes: satellites, facility speaker, and subwoofer. The X-530’s satellites and facility speaker use twin 2-inch drivers to generate treble and midrange frequencies. The ported subwoofer uses a 5.25-inch driver. The X-530 has a typical power level for the price point. Its two subwoofers have a combined power of 70 watts.
Specifications
- Total RMS Power: 70.1 Watts
- Subwoofer: 25 watts RMS into 4 ohms at 100Hz at 10% THD clipping (total harmonic distortion)
- Satellites: 45.1 watts RMS (2 x 7.4 w Front; 15.5 w Center: 2 x 7.4 w Rear ) into 4 ohms at 1 kHz at 10% THD clipping (total harmonic distortion)
- Total Peak Power: 140 Watts at <10% THD
- System THD: Better than 0.07% THD before clipping
- Signal to noise ratio: >99 dB
- Frequency response: 40 Hz – 20 kHz
- Driver Size: 2” high excursion satellites, 5.25” high excursion subwoofer
- Satellites: (H) 8” x (W) 2.5” x (D) 3”
- Center: (H) 2.5” x (W) 8” x (D) 3”
- Setup Subwoofer: (H) 11.5” x (W) 6” x (D) 9.25”
Logitech X-530 User Manual Download
- Setup Guide (PDF) [333 KB] DOWNLOAD
Logitech X-530 5.1 Speaker System Driver for Windows
| Hardware | Logitech X-530 |
| Category | Speaker |
| File Languages | Multi-language |
| Last Update | 2022-01-25 |
| File Size | 40 Mb |
| Version | 2022.2.659 |
| Operating System | Windows 10, Windows 11 |
Link Download Logitech X-530 Driver for Windows
- Logitech Driver [40 MB] No drivers needed
Logitech X-530 5.1 Drivers for Mac
| Hardware | Logitech X-530 |
| Category | Speaker |
| File Languages | Multi-language |
| Last Update | 2022-01-25 |
| version | 2022.2.659 |
| Size | 16 Mb |
| Operating System | macOS 10.15, macOS 11, macOS 12.0 |
Link Download Logitech X-530 Drivers for Mac
- Logitech driver[16 Mb] No drivers needed
Setting Logitech® X-530 speakers
- Before attaching the cables to the subwoofer, position the two front satellite speakers on either side of your computer monitor about the same distance from each other as from you. Angle them to face you. The right front speaker is the control center for your system, so you will want to place it within easy reach. Place the rear left and right satellite
speakers behind you and about the same distance apart as the front speakers. Position the front center channel speaker on top of your monitor or on your desk in between your monitor and keyboard. Depending on where you place your speakers, adjust the stand to direct the sound toward you.
For best sound quality, place the subwoofer on the floor beneath your desk. Be sure to maintain at least 6 inches of spacing around the subwoofer to allow for adequate ventilation.
- Insert the colored plug from each satellite speaker into the corresponding colored jacks on the back of the subwoofer. Connect the d-sub plug from the front right speaker to the subwoofer as shown on the previous page. Carefully align the pins before inserting the plug, and screw down the connector.
- If you have a PC and a:
• 6, 7 or 8 channel (5.1, 6.1 or 7.1) sound card: Connect all 3 colored plugs from the audio input cable to the color coded jacks on the sound card.If jacks on your soundcard are not color coded, plug the audio input as follows:
• green to front L/R (or #1)
• black to rear L/R (or #2)
• orange to center / sub (or #3)• 4-channel sound card: Connect the green plug from the audio input cable to your sound card’s front jack and the black plug to your sound card’s rear jack. Do not use the orange plug.
• 2-channel sound card: Connect the green plug from the audio input cable to the “line out” jack on your sound card. Do not use the black or orange plugs. With a 2-channel sound card you will not hear sound from the rear speakers.If you have a video game console (PlayStation®, PlayStation®2, Xbox™, or GameCube®):
• Connect the green, black and orange plugs from the audio input cable to the 3 stereo mini jacks on the video game adapter.
• Connect the red and white RCA audio cables from your video game console to the RCA audio jacks to the video game adapter. - Plug the subwoofer’s power cord into an electrical outlet.
